Hach-lange ORBISPHERE Model 51x User Manual Manuel d'utilisateur Page 41
- Page / 116
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
39
Installation
Note: When changing the type of sensor (e.g. from a 31xxx EC sensor to a 31xxxS smart EC sensor)
please contact your local Hach Lange representative.
3.9 Measurement alarm relays
Analog inputs (when ext. press. sensor is
directly connected)
12. EC sensor: Not used
TC sensor: GND
13. Green: Input ext. press. sensor P+
14. White: Input ext. press. sensor P-
15. Red: Output ext. press. sensor +
16. Black: Ground (GND)
Analog inputs (when ext. press. sensor
extension, Part N° 32548.xx, is used)
12. EC sensor: Not used
TC sensor: GND
13. Green: Input ext. press. sensor P+
14. Yellow: Input ext. press. sensor P-
15. White: Output ext. press. sensor +
16. Brown: Ground (GND)
Note: On multi channel systems, the external pressure sensor must be wired to the channel 1
measurement board, but the signal is used to compensate all channels.
Connector J8 (sensor)
Note: Remember, this connector is colored orange for EC sensors and black for TC sensors.
A1100 EC sensor 31xxx EC sensor
31xxxS smart EC
sensor
TC sensor
Cable
sensor
wall/panel
mount
LEMO 10
sensor
portable
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
Guard electrode
RS485A+
Thermistor A
Anode electrode
RS485B-
Thermistor B
GND
+ 5V
Cathode electrode
Not used
Guard electrode
Not used
Thermistor A
Anode electrode
Not used
Thermistor B
Not used
Not used
Cathode electrode
Not used
Guard electrode
I2C-SCL
Thermistor A
Anode electrode
I2C-SDA
Thermistor B
GND
+ 5V
Cathode electrode
Not used
GND for power
V2 signal
Solenoid
Relay coil
+12V power
+24V power
V3 signal
GND for signal
-5V power
Temperature
Yellow
Pink
Grey
Red
Purple
White
Black
Green
Blue
Brown
Brown
Red
Orange
Yellow
Green
Blue
Purple
Grey
White
Black
Figure 21 Output relays
The three output relays are located on the measurement
board (see also Figure 17 and Figure 18 on page 38).
They can be individually configured to Normally Open (NO) or
to Normally Closed (NC) by physically moving the jumper on
each relay. The picture example on the left (EC measurement
board):
• Upper relay is set to NC
• Middle relay is set to NO
• Lower relay is shown with no jumper, to show the 3 pins.
Note: For all measurement boards, J4 is relay 1, J5 is relay 2 and J6
is relay 3
- ORBISPHERE Model 51x Analyzer 1
- Table of Contents 3
- Section 1 General Information 7
- 1.3.2 Safety precautions 8
- 1.3.3 Service and repairs 8
- 1.3.4 Precautionary labels 9
- General Information 10
- 1.5 Product disposal 12
- Section 2 Specifications 15
- Specifications 16
- 2.2 Hardware description 17
- 2.4 Security level table 20
- 2.5 Default parameters 21
- Section 3 Installation 23
- 3.2 Installation check list 24
- Installation 25
- 3.3.1 Instrument dimensions 25
- 3.3.2 Wall mounting 26
- 3.3.3 Pipe mounting 26
- 3.4 Panel mount instrument 29
- 3.4.2 Mounting 30
- 3.5 Portable table instrument 32
- 3.5.2 Mounting 33
- 3.8.1 Sensor cable 38
- 3.8.3 Main board connections 39
- 3.8.4 Measurement board 40
- 3.9 Measurement alarm relays 41
- 3.10 Sensor installation 42
- Section 4 User Interface 43
- User Interface 44
- 4.2.3 Menu navigation 45
- 4.2.4 Rolling list 45
- 4.2.5 Virtual keyboard 46
- 4.2.7 Warning windows 46
- 4.3 Main menu structure 47
- Section 5 View Menu 49
- View Menu 50
- Section 6 Measurement Menu 53
- 6.1 Instrument configuration 54
- 6.2 Measurement configuration 55
- Measurement Menu 56
- Section 7 Calibration menu 61
- Calibration menu 62
- 7.1 Definitions 63
- 7.2 EC gas sensor calibration 63
- sensor calibration 64
- 7.3 TC gas sensor calibration 65
- 7.9 Calibration reports 68
- Section 8 Inputs/Outputs Menu 69
- 8.1 Configure snooze 70
- 8.2 View inputs/outputs 70
- 8.3 Relays 70
- 8.4 Analog outputs 71
- Inputs/Outputs Menu 72
- Section 9 Communication Menu 79
- Communication Menu 80
- 9.1.1 Data available 81
- 9.1.2 Example of use 84
- 9.2.1 Installation 85
- 9.2.2 Input/Output data 86
- 9.3 USB-A port (host) 89
- 9.4 HTTP/TCP-IP 90
- 9.5.3 Upload report files 92
- Section 10 Security Menu 95
- 10.2 Configure security 96
- 10.3 User management 96
- 10.4 User action log file 96
- Section 11 Products Menu 97
- Products Menu 98
- Global Configuration Menu 100
- Section 13 Services menu 101
- Services menu 102
- 13.1 Sensor diagnostics 103
- 13.5 Buzzer 104
- 13.6 Boards info 104
- 13.2 Language selection 104
- 13.3 Clock 104
- 13.4Screen 104
- 13.7 Batteries 105
- 13.8 Software download 105
- 13.9 End application 105
- 14.1 Instrument maintenance 107
- 14.2 Troubleshooting 107
- Table 4 List of Events 108
- Section 15 Part Lists 111
- 15.2 Spare parts 112
- Section 16 Glossary 113
- Glossary 114
Produits connexes et manuels pour Équipement Hach-lange ORBISPHERE Model 51x User Manual
(100 pages)
(190 pages)
(302 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.145 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels