Hach-lange ORBISPHERE 410 Basic User Manual Manuel d'utilisateur Page 18
- Page / 190
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Option Description
Offset and slope
corrections
Enable correction as appropriate. If enabled, the correction values for offset and
slope must be entered. These values cannot be negative.
Liquid to gas factor Enable correction as appropriate. If checked, the percentage correction factor
must be entered. This value cannot be negative.
Note: If you believe you need to enable these corrections, it is advisable to
contact a Hach Lange Service Representative first.
Interferences configuration
These options are available to take into account the influence of some components or gases in the
sample during measurement. All available interference corrections are disabled by default.
The following interference corrections are available:
• For oxygen measurements - CO
2
, H
2
S, Chlorine, Salt
Note: If you believe you need to enable any of the above, it is advisable to contact a Hach Lange Service
Representative first.
Interferences in oxygen measurement
In some applications, like in the beverage industry, there can be high concentrations of carbon
dioxide in the sample. Hach Lange recommends using the CO
2
interference option if a carbon
dioxide concentration of over 1% in gas phase, or 15 ppm in dissolved phase is present.
In the petroleum industry, the detection of oxygen is sometimes hampered by significant
concentrations of hydrogen sulfide in the sample. Hach Lange recommends using the H
2
S
interference option if the hydrogen sulfide concentration exceeds 0.15% in gas phase, or 5 ppm in
dissolved phase. To operate the oxygen sensor in these conditions requires using a different
sensor and electrolyte. When using this mode your system will experience sensitivity loss of about
50 times higher than the minimum sensitivity for the membrane.
1. Proceed as follows:
Option Description
CO2 or H2S Select CO
2
, H
2
S or All disabled.
Chlorinity/Salinity Select Chlorinity, Salt or All disabled. For chlorinity or salt, it is required to enter the
actual concentration in the sample.
Measured data storage
There is one measurement file which contains the data generated by the measurement cycle. The
measurement file is updated in volatile memory and regularly copied in non-volatile memory (file
back-up). At start up the measurement file in volatile memory is updated with the file from the non-
volatile memory.
Note: Data stored in volatile memory is lost when instrument is powered off; non-volatile memory is permanent. In
case of an accidental power off event the instrument resumes measurement storage after the last measurement
stored in flash.
1. Select Measurement file from the Measurement menu:
Option Description
Storage mode Select No storage if data storage is not required. Select Store once to start
recording measurements. When the volatile memory is full the recording of
measurement stops. Select Rolling buffer for continuous recording of
measurements. When the volatile memory is full the latest measurement set
replaces the oldest one (first-in, first-out)
RAM time The delay between two recordings of measurement data.
18 English
- ORBISPHERE Model 1
- 410 Analyzer 1
- Specifications 3
- General information 4
- Pipe mounting 6
- Panel mounting 6
- Instrument connections 7
- W A R N I N G 7
- C A U T I O N 8
- N O T I C E 10
- User interface 12
- Security menu 13
- View menu 14
- Measurement menu 15
- Measurement configuration 16
- Advanced configuration 17
- Interferences configuration 18
- Measured data storage 18
- Calibration 19
- sensor calibration 20
- TC gas sensor calibration 21
- Services menu 22
- Other menus 22
- Maintenance 22
- Spezifikationen 23
- Allgemeine Informationen 24
- Rohrmontage 26
- Anschlüsse des Instruments 27
- W A R N U N G 27
- H I N W E I S 28
- V O R S I C H T 28
- Sensorinstallation 32
- Benutzeroberfläche 33
- Menü Sicherheit 34
- Menü Auswertung 35
- Menü Messung 35
- Konfigurierung der Messung 36
- Erweiterte Konfigurierung 38
- Konfiguration der Interferenz 38
- Kalibrierung 39
- Definitionen 40
- -Sensor kalibrieren 41
- -Sensor kalibrieren 41
- Menü Wartung 42
- Sonstige Menüs 43
- Specifiche 44
- Informazioni generali 45
- Installazione 46
- Montaggio a parete 47
- Montaggio su tubo 47
- Montaggio su pannello 47
- Connessioni dello strumento 48
- A V V E R T E N Z A 48
- A V V I S O 49
- A T T E N Z I O N E 49
- Installazione del sensore 53
- Interfaccia utente 54
- Menu sicurezza 54
- Menu vista 55
- Menu misura 56
- Configurazione filtro misure 58
- Configurazione avanzata 58
- Calibrazione 60
- Taratura del gas misurato 61
- Taratura del sensore di O 61
- Calibrazione del gas misurato 62
- Menu servizi 63
- Altri menu 64
- Manutenzione 64
- Spécifications 65
- Généralités 66
- Étiquettes de mise en garde 67
- D A N G E R 67
- A V E R T I S S E M E N T 67
- 68 Français 68
- Branchement au secteur 70
- A T T E N T I O N 70
- Carte mère 72
- Carte de mesure 72
- Installation du capteur 74
- Interface utilisateur 75
- Menu sécurité 76
- Menu d'affichage 77
- Menu de mesure 77
- Configuration de mesure 78
- Configuration avancée 79
- Configuration interférence 80
- Stockage des données mesurées 80
- Étalonnage 81
- Étalonnage du gaz mesuré 82
- Étalonnage du capteur O 82
- Étalonnage capteur de gaz TC 83
- Menu des services 84
- Autres menus 85
- Entretien 85
- Especificaciones 86
- Información general 87
- Instalación 88
- Montaje en pared 89
- Montaje en tubería 89
- Montaje en panel 89
- Conexiones del instrumento 90
- A D V E R T E N C I A 90
- A V I S O 91
- P R E C A U C I Ó N 91
- Instalación del sensor 95
- Interfaz de usuario 96
- Menú seguridad 96
- Menú vista 97
- Menú medición 98
- Configuración de la medición 99
- Configuración avanzada 100
- Almacenado de datos medidos 101
- Calibración 102
- Calibración del gas medido 103
- Calibración del sensor de O 103
- Menú servicios 105
- Otros menús 106
- Mantenimiento 106
- Technické údaje 107
- Obecné informace 108
- Instalace 109
- Montáž na stěnu 110
- Montáž k trubce 110
- Montáž do panelu 110
- Připojení přístroje 111
- V A R O V Á N Í 111
- U P O Z O R N Ě N Í 112
- Připojení k síťovému napájení 112
- P O Z O R 112
- Instalace senzoru 116
- Uživatelské rozhraní 117
- Konfigurace zabezpečení 118
- Správa přístupových práv 118
- Správa uživatelů 118
- Nabídka View (Zobrazení) 119
- Nabídka měření 119
- Konfigurace měření 120
- Konfigurace alarmů měření 121
- Konfigurace filtru měření 121
- Pokročilé nastavení 122
- Konfigurace interferencí 122
- Kalibrace 123
- Definice 124
- Kalibrace O 125
- senzoru 125
- Kalibrace měřeného plynu 125
- Nabídka Services (Servisy) 126
- Jiné nabídky 127
- Specifikationer 128
- Generelle oplysninger 129
- Installation 130
- Vægmontering 131
- Rørmontering 131
- Panelmontering 131
- Instrumentforbindelser 132
- A D V A R S E L 132
- B E M Æ R K N I N G 133
- F O R S I G T I G 133
- Brugergrænseflade 137
- Sikkerhedsmenu 138
- Vis menu 139
- Målemenu 140
- Konfiguration af måling 141
- Konfiguration af målefilter 142
- Avanceret opsætning 142
- Interferensopsætning 143
- Måling af data 143
- Kalibrering 144
- sensorkalibrering 145
- TC-gassensorkalibrering 146
- Kalibrering af barometertryk 146
- Eftersynsmenu 147
- Øvrige menuer 147
- Vedligeholdelse 147
- Specificaties 148
- Algemene informatie 149
- Installatie 150
- Wandmontage 151
- Buismontage 151
- Paneelmontage 151
- W A A R S C H U W I N G 152
- L E T O P 153
- Aansluiten op de netvoeding 153
- V O O R Z I C H T I G 153
- De sensor monteren 157
- Gebruikersinterface 158
- Menu Security 158
- Beveiligingsconfiguratie 159
- Beheer van toegangsrechten 159
- Gebruikersbeheer 159
- Menu View 160
- Menu Measurement 160
- Meetconfiguratie 161
- Configuratie meetalarmen 162
- Configuratie meetfilter 162
- Geavanceerde configuratie 163
- Interferentieconfiguratie 163
- Kalibratie 165
- -sensorkalibratie 166
- TC-gassensorkalibratie 167
- Andere menu's 168
- Onderhoud 168
- Menu Services (diensten) 168
- Teknik Özellikler 169
- Genel Bilgiler 170
- Duvara takılması 172
- Boruya takılması 172
- Panele takılması 172
- Cihaz bağlantıları 173
- U Y A R I 173
- B İ L G İ 174
- Şebeke gerilimi bağlantısı 174
- D İ K K A T 174
- Sensör kurulumu 178
- Kullanıcı arayüzü 179
- Güvenlik menüsü 179
- Erişim hakları yönetimi 180
- Kullanıcı yönetimi 180
- Görüntü menüsü 181
- Ölçüm menüsü 181
- Ölçüm yapılandırması 182
- Gelişmiş yapılandırma 183
- Girişim Yapılandırma 184
- Ölçüm verisi kaydı 184
- Kalibrasyon 185
- sensör kalibrasyonu 186
- TC gaz sensörü kalibrasyonu 187
- Bakım menüsü 188
- Diğer menüler 188
- Hach Lange, 2006-2013 190
Produits connexes et manuels pour Équipement Hach-lange ORBISPHERE 410 Basic User Manual
(204 pages)
(302 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.446 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels