Hach-lange ORBISPHERE K1100_M1100 Operator Manual Manuel d'utilisateur Page 98
- Page / 114
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
96
Services Menu
13.4 Screen
13.5 Buzzer
13.6 Boards info
13.7 Batteries
13.8 Software download
13.9 End application
Screen
Screen calibration This screen allows you to adjust the click position corresponding to the
displayed buttons. Use it if ever the sensitive areas are no longer properly
aligned with the buttons on display.
Place the stylus right on the cross when asked and proceed. User will be
asked to press on the screen to accept the new setting. If not, the new
setting is not recorded and no change is made.
Screen brightness Press the up or down arrow to increase or decrease the screen brightness.
Four levels are pre-set: Max, Comfortable, Standard (default setting) and
Economy. Press OK when finished.
Note: This can also be called through the brightness icon on the
main display.
Buzzer
Adjust the sounds available on the instrument.
When “screen tap” is enabled, a click sound is heard each time the screen is touched.
The instrument alarm sound can be enabled or disabled to suit the application. The sound type can also
be adjusted. Press the Test button to test the adjustment made. Press again to stop.
Boards info
Main board info For reference, this display gives information on the instrument model,
software version and instrument ID.
Measurement board info For reference, this display gives information on the sensor measurement
board hardware and software.
Pressing the Analog outputs corr. button displays the correction factor that
is applied to the analog outputs.
Pressing the Amplifiers corr. button displays the value of the actual
correction factor on the amplifiers.
Sensor parameters For reference this display gives information on the sensor model and type,
last calibration, settings and behavior.
Batteries
On all instruments this display gives the real time clock battery charge level and voltage.
Note: A warning message (and icon) is displayed if the battery level becomes too low and needs to be
replaced.
Software download
For Hach Lange technician use only. Used when reloading the software for new versions.
This ends the application. User must stop and restart the instrument to restart the program.
End application
This ends the application. User must stop and restart the instrument to restart the program.
- 410 Analyzer 1
- Table of Contents 3
- Section 1 General Information 7
- 1.3.2 Safety precautions 8
- 1.3.3 Service and repairs 8
- 1.3.4 Precautionary labels 9
- General Information 10
- 1.5 Product disposal 12
- Section 2 Specifications 15
- Specifications 16
- 2.4 Hardware description 18
- 2.5 Security level table 19
- 2.6 Default parameters 20
- 2.7 M1100 EHEDG Certification 21
- Section 3 Installation 23
- 3.2 Installation check list 24
- Installation 25
- 3.3.1 Instrument dimensions 25
- 3.3.2 Wall mounting 26
- 3.3.3 Pipe mounting 26
- 3.4 Panel mount instrument 28
- 3.4.2 Mounting 29
- 3.7.2 Main board connections 35
- 3.8 Measurement alarm relays 36
- 3.9 Sensor installation 37
- 3.9.4 Sensor removal 38
- 3.10 Calibration devices 40
- Section 4 User Interface 43
- User Interface 44
- 4.2.2 Menu navigation 45
- 4.2.3 Rolling list 45
- 4.2.4 Virtual keyboard 45
- 4.2.6 Warning windows 46
- 4.3 Main menu structure 47
- Section 5 View Menu 49
- View Menu 50
- Section 6 Measurement Menu 53
- 6.2 Measurement configuration 54
- Measurement Menu 55
- 6.3 Measured data storage 56
- Section 7 Calibration Menu 57
- 7.1 Sensor calibration 58
- 7.2 Calibration configuration 59
- 7.3 Zero calibration 60
- 7.5 High level adjustment 60
- 7.6 Sensor verification 60
- 7.8 Calibration reports 61
- Calibration Menu 62
- Section 8 Inputs/Outputs Menu 63
- 8.1 Configure snooze 64
- 8.2 View inputs/outputs 64
- 8.3 Relays 64
- 8.4 Analog outputs 65
- Inputs/Outputs Menu 66
- Section 9 Communication Menu 73
- Communication Menu 74
- 9.1.1 Data available 75
- 9.1.2 Example of use 78
- 9.2.1 Installation 79
- 9.2.2 Input/Output data 80
- 9.3 USB-A port (host) 83
- 9.4 HTTP/TCP-IP 84
- 9.5.3 Upload report files 86
- 9.6 Printer 88
- Section 10 Security Menu 89
- 10.2 Configure security 90
- 10.3 User management 90
- 10.4 User action log file 90
- Section 11 Products Menu 91
- Products Menu 92
- Global Configuration Menu 94
- Section 13 Services Menu 95
- Services Menu 96
- 13.1 Sensor diagnostics 97
- 13.2 Language selection 97
- 13.3 Clock 97
- 14.1 Instrument maintenance 99
- 14.2 Sensor maintenance 99
- 14.4 Troubleshooting 101
- Table 4 List of Events 103
- 15.1 Instrument 105
- 15.2 Sensor 105
- Accessories and Spare Parts 106
- 15.6 Instrument options 109
- Section 16 Glossary 111
- Glossary 112
Produits connexes et manuels pour Équipement Hach-lange ORBISPHERE K1100_M1100 Operator Manual
(76 pages)
(302 pages)
© 2020, manymanuals.fr. Tous droits réservés | 5.087 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels